Unication Messenger m90 Manual de usuario Pagina 110
- Pagina / 407
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
U90 Ladder Software Manual
102
77 Dial Remote
Modem
Dials the phone number represented by the index number
stored in SI 71
System Integers
SI Symbol Description
70 Modem: Error
Code
Contains an error code resulting from a modem error. The list
is shown below.
71 Modem: Phone
Number
Contains the phone number to be dialed. You create a phone
book when you configure the modem. Each phone number in the
phone book is linked to an index number.
Use the Store Direct function to place the index number of
desired phone number in SI 71, then activate SB 77 to dial it.
Error Messages ( SI 70)
Number Error Message Description
0 No Error No error.
1 No Carrier No carrier signal found--reason unknown. Check your
communication cables.
2 Modem Did Not
Reply
The modem referred to is the one on the M90 side.
3 No Dial Tone No dial tone.
4 Line is Busy The number dialed is engaged.
5 No Carrier While
Dialing
Carrier signal was lost during dialing.
6 Modem Report
Error
May be due to an incorrect number or unknown
initialization commands.
7 Modem Report
Unknown Message
An unrecognized message.
8 No Phone Number SI 71 contains a number that is not linked to any phone
number stored in the phone book.
9 RS232 Port Busy The RS232 port is already in use.
SMS System Bits and Integers
Listed below are the System Bits, System Integers, and Error Messages that are used by
the M90 in SMS messaging.
System Bits
SB Symbol Description
180 Initialize GSM
Modem for
SMS
This is necessary to enable use of the SMS feature. Note that the
modem must first be initialized using SB 70.
181 SMS:
Initialization
Succeeded
Signals that GSM modem has been initialized. The modem is now
ready to send and receive SMS messages.
182 SMS:
Initialization
Failed
Signals that GSM modem has failed. SI 180 contains the error code.
183 Send SMS Send the string that is represented by the index number stored in SI
182, to the phone number represented by the index number stored
in SI 181.
184 SMS:
Transmission
succeeded
Signals that SMS has been successfully transmitted
185 SMS:
Transmission
Failed
Signals that SMS has failed. SI 180 contains the error code
186 SMS Received Signals that a defined SMS has been received. SI 183 contains the
index number identifying the origin of the SMS, if this number has
been stored in the SMS phone book. If the number is not found, SI
- U90 Ladder Software Manual 1
- Table Of Contents 3
- Welcome to U90 Ladder 9
- Printing Documentation 10
- Interface Language 10
- Getting Started 11
- Uploading a Project 12
- Project Properties 13
- Ladder Editor 17
- Using the HMI Display Editor 17
- Comments Tool 18
- Power-up 19
- Hardware Configuration 21
- Configuring an Analog Input 38
- Analog I/O Ranges 43
- High-Speed Output: PWM 49
- Display 55
- Variable 75
- Changing Mode via Ladder 96
- Dialing a remote M90 99
- Communication Log 100
- M90 modem configuration 106
- Modems: General 109
- Communications 111
- Networks 112
- Creating SMS text messages 120
- Attaching variables 120
- Deleting variables 121
- Testing messages 121
- Variable Types 122
- ACK-Acknowledge message 123
- Problem SI 180 133
- Ladder Net 135
- Placing Contacts & Coils 136
- Placing a Function Block 138
- Ladder Logic 140
- Comments 140
- Copy and Paste Elements 142
- Copying multiple nets 143
- Moving Elements 145
- Replacing Ladder elements 146
- Restoring System Symbols 148
- Scrolling between nets 149
- Intersecting lines: Junction 153
- Ladder Nets with Feedbacks 153
- Elements 154
- Operands 161
- Functions 175
- Equal 177
- Greater or Equal 177
- Greater Than 178
- Less or Equal 178
- Less Than 179
- Not Equal 179
- Using the Compare function 180
- AND Example 183
- Add Examples 189
- Divide 190
- Division Examples 191
- Multiply 193
- Multiplication Examples 194
- Subtract 195
- Subtraction Examples 195
- Store Direct function 197
- Store Indirect function 199
- Clock Functions 200
- Direct Clock function 201
- Indirect Clock function 206
- Linearization 214
- Load Indirect 217
- Copy Vector 218
- Fill Vector 219
- Function Number 220
- (SI 140) 220
- Description 220
- 30 Fill MI Vector 220
- 31 Fill DB Vector 220
- Square Root 223
- Communication Utilities 226
- Interrupt 228
- Example 229
- Convert MB to MI, MI to MB 230
- Shift Register 233
- Counter 236
- Proportional Band 242
- Integral Action 243
- Derivative Action 244
- PID Function Parameters 245
- Utilities 249
- Verify Project 251
- M90 Downloader 252
- Battery Back-up values 253
- Find and Replace Elements 254
- Program Password Protection 255
- Examples 264
- General 269
- HSC Types & Functions 293
- To Create a Field 306
- To Attach a Variable 307
- Writing Values 356
- Reading Values 356
- Linearize values for Display 358
- Phone Book 373
- Modem commands 380
- Modem Connections 381
- GSM modems 385
- Modem Commands 393
- Troubleshooting 399
- CANbus network problems 402
- M90 does not turn on 402
- Power-up Modes 403
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales